Exactly How to Remove and Change a Bathtub

Schedule Appointment

They are making several great pointers on the subject of How to Install a Bathtub as a whole in this great article following next.

Tools You Need to Install a New Bathtub
Mounting a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is readily obtainable, the job can move immediately; if you have to open up a wall to remove the old bathtub and place the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to consider using one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you install a brand-new bath tub in your shower room if you have currently bought a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and material list must comprise the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps

  • Planning for the Installation

    First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
    Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.

    Removing Old Touches

    If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic due to the restricted gain access to that is usually the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Bathtub

    Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
    The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the tub till the level reads level.
    To mount taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
    Turn on the supply of water and also inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise inspect the overflow outlet and the regular electrical outlet for leaks.
    Ultimately, deal with the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the tub should wait till the tub has actually been utilized at least once as this will resolve it into its last position.

    Suitable New Taps

    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Tub

    In the area where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, bring about complications with dampness as well as feasible leaks to the ceiling listed below.
    You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not think about this motion prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and cement.

    How to Install or Replace a Bathtub

    Find Your Dimensions

    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

    Disconnect the Water Supply and Drain Assembly

    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

    Cut Out the Old Tub

    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

    Install the New Tub

    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

    Secure the Tub

    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We were guided to that report on How to Install a Bathtub through someone on our other web address. Are you aware of somebody who is curious about Tools You Need to Install a New Bathtub ? Be sure promote it. Thanks so much for taking the time to read it.

    Book Your Service

    Leave a Reply

    Your email address will not be published. Required fields are marked *